Instrukcja obsługi ASUS P1

[. . . ] Use of some of these modes will not be possible with this projector. · Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of display pixels above. · Although the projector can display signals with resolution up to UXGA (1600x1200), the signal will be converted to the projector's panel resolution before being displayed. [. . . ] · Although the projector can display signals with resolution up to UXGA (1600x1200), the signal will be converted to the projector's panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and projector panel are identical. · Automatically adjustment may not function correctly with some input signals. · The image may not be displayed correctly when the input sync signal is a composite sync or a sync on G. 1 Example of computer signal Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Data H. Sync (A) Front porch (D) Back porch (b) Data V. Sync (a) Front porch (d) Display interval (C) Display interval (c) Computer/ Signal TEXT VGA (60Hz) VGA (72Hz) VGA (75Hz) VGA (85Hz) SVGA (56Hz) SVGA (60Hz) SVGA (72Hz) SVGA (75Hz) SVGA (85Hz) Mac 16" mode XGA (60Hz) XGA (70Hz) XGA (75Hz) XGA (85Hz) 1152 x 864 (75Hz) 1280 x 960 (60Hz) SXGA (60Hz) SXGA (75Hz) SXGA (85Hz) UXGA (60Hz) W-XGA (60Hz) SXGA+ (60Hz) (A) 2. 0 3. 8 1. 3 2. 0 1. 6 2. 0 3. 2 2. 4 1. 6 1. 1 1. 1 2. 1 1. 8 1. 2 1. 0 1. 2 1. 0 1. 0 1. 1 1. 0 1. 2 1. 7 1. 2 (B) 3. 0 1. 9 4. 1 3. 8 2. 2 3. 6 2. 2 1. 3 3. 2 2. 7 3. 9 2. 5 1. 9 2. 2 2. 2 2. 4 2. 9 2. 3 1. 8 1. 4 1. 9 2. 5 2. 0 (C) 20. 3 25. 4 20. 3 20. 3 17. 8 22. 2 20. 0 16. 0 16. 2 14. 2 14. 5 15. 8 13. 7 13. 0 10. 8 10. 7 11. 9 11. 9 9. 5 8. 1 9. 9 16. 0 11. 4 (D) 1. 0 0. 6 0. 8 0. 5 1. 6 0. 7 1. 0 1. 1 0. 3 0. 6 0. 6 0. 4 0. 3 0. 2 0. 5 0. 6 0. 9 0. 4 0. 1 0. 4 0. 4 0. 8 0. 7 Computer/ Vertical signal timing (lines) Signal (a) (b) (c) (d) TEXT 3 42 400 1 VGA (60Hz) 2 33 480 10 VGA (72Hz) 3 28 480 9 VGA (75Hz) 3 16 480 1 VGA (85Hz) 3 25 480 1 SVGA (56Hz) 2 22 600 1 SVGA (60Hz) 4 23 600 1 SVGA (72Hz) 6 23 600 37 SVGA (75Hz) 3 21 600 1 SVGA (85Hz) 3 27 600 1 Mac 16" mode 3 39 624 1 XGA (60Hz) 6 29 768 3 XGA (70Hz) 6 29 768 3 XGA (75Hz) 3 28 768 1 XGA (85Hz) 3 36 768 1 1152 x 864 3 32 864 1 (75Hz) 1280 x 960 3 36 960 1 (60Hz) SXGA(60Hz) 3 38 1024 1 SXGA (75Hz) 3 38 1024 1 SXGA (85Hz) 3 44 1024 1 UXGA (60Hz) 3 46 1200 1 W-XGA (60Hz) 3 23 768 1 SXGA+ (60Hz) 3 33 1050 1 2 Connection to the ports Connection to the ports A Y AUDIO IN3 R RGB IN1 CB/PB CR/PR K B C RGB IN2 RGB OUT AUDIO OUT L AUDIO IN1 AUDIO IN2 CONTROL USB VIDEO S-VIDEO A RGB IN1, B RGB IN2, C RGB OUT D-sub 15pin mini shrink jack · Video signal: RGB separate, Analog, 0. 7Vp-p, · H/V. Signal: TTL level (positive/negative) · Composite sync. Signal: TTL level 5 10 4 9 3 8 2 7 1 6 15 14 13 12 11 At RGB signal Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Signal Video Red Video Green Video Blue (No connection) Ground Ground Red Ground Green Ground Blue (No connection) Ground (No connection) A : SDA (DDC data), B / C : (No connection) H. (3) The projector returns the response code `06H' to the computer. Decreasing the projector setting value (Decrement command) (1) The computer sends the decrement code Header + Command data (`05H'+ `00H'+ type (2 bytes) +`00H' + `00H') to the projector. (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code `06H' to the computer. When the projector cannot understand the received command When the projector cannot understand the received command, the error code `15H' is sent back to the computer. Sometimes the projector cannot properly receive the command. In such a case, the command is not executed and the error code `15H' is sent back to the computer. If this error code is returned, send the same command again. When the projector cannot execute the received command. When the projector cannot execute the received command, the error code `1CH' + `xxxxH' is sent back to the computer. [. . . ] When the projector cannot execute the received command. When the projector cannot execute the received command, the error code `1CH' + `xxxxH' is sent back to the computer. Japan 292 Yoshida-cho Totsuka-ku, Yokohama-city Kanagawa 244-0817 ASUS EUROPE LTD. Consumer Affairs Department PO Box 3007 Maidenhead SL6 8ZE UNITED KINGDOM Tel: 0870 405 4405 Email: consumer. mail@Hitachi-eu. com ASUS EUROPE GmbH Munich Office Dornacher Strasse 3 D-85622 Feldkirchen bei München GERMANY Tel: +49 -89-991 80-0 Fax: +49 - 89 - 991 80 -224 Hotline: +49 - 180 - 551 25 51 (12ct/min. ) Email: HSE-DUS. Service@Hitachi-eu. com ASUS EUROPE SRL Via T. [. . . ]